Description: 由于DS1624是I2C总线结构的串行数据传送，它只需要SDA和SCL两根线完成数据的传送过程。因此，我们在进行程序设计的时候，也得按着I2C协议来对DS1624芯片数据访问。有关I2C协议参看有关资料，这里不详述。对于AT89S51单片机本身没有I2C硬件资源，所以必须用软件来模拟I2C协议过程。
要从DS1624中读取温度值，首先启动DS1624的内部温度A/D开始转换，对应着有相应的命令用来启动开始温度转换，有关DS1624的指令集参考前面的叙述。一般情况下，DS1624经过一次温度的变换，需要经过1秒钟左右的时间，所以等待1秒钟后，即可读取内部的温度值，对于读取的温度值，仍然通过DS1624的指令集来完成温度的读取。但所有有数据的传送过程必须遵循I2C协议。
-DS1624 is due to the structure of I2C bus serial data transmission, it requires SDA and SCL completed two lines of data transmission process. Therefore, we design procedures during the time, it has agreed to subscribe for I2C chip DS1624 data access. The I2C agreement refer to the relevant information, will not elaborate here. For AT89S51 SCM does not I2C hardware resources, Therefore, we must use the software to simulate the process I2C agreement. Read from the DS1624 temperature, to start the internal temperature DS1624 A / D conversion start, corresponds to a corresponding order to start the starting temperature conversion, the DS1624 instruction set reference to the previous description. Under normal circumstances, the DS1624 temperature through a transformation takes a second time aro Platform: |
Size: 1702 |
Author:花花 |
Hits:
Description: MCS-96单片机A_D转换器应用-通过检测AD_RESULT（LO）中的S位来判定A/D转换是否完成。需要注意的是，当发出启动A/D转换命令后，AD_RESULT中的S位要经过8个状态周期后才能对其查询.-MCS-96 microcontroller A_D converter applications-through detection AD_RESULT (LO) the S to determine A / D converter whether completed. We need to be aware that when issued start A / D conversion orders, AD_RESULT the S-8 to go through cycle after the state of its inquiries. Platform: |
Size: 3928 |
Author:容健 |
Hits:
Description: 通过改变LINE_IN端口的模拟电压来改变IOB口输出的数据，采用读取P_ADC_MUX_Ctrl寄存器启动ADC转换，可以通过发光二极管的点亮了解转换的数据值。可以作为初学者入门的小程序.-LINE_IN port by changing the simulation to change the voltage output IOB population data, Register used to read P_ADC_MUX_Ctrl start ADC conversion, through the LED lights understanding of the data conversion value. Getting Started as a small beginners procedures. Platform: |
Size: 8782 |
Author:kevin |
Hits:
Description: 单片机和PC机串口通讯实例说明
首先打开串口调试程序并按要求设置。启动51板后，按S10切换至接收状态，按S12切换至发送状态，启动默认为发送状态。
发送状态：
进入发送状态后，可向PC发送1-9 9个数字，并且数码显示同时显示发送的数，按S1发送1，按S2发送2，依次到按S9发送9。S11无用。发送成功可在串口调试程序的数据接收栏中显示收到的数据。
发送状态：
进入发送状态后，在串口调试程序的数据发送栏中输入00-FF的16进制2位数，点击手动发送，如发送成功，51版将16进制数通过程序转换为10进制数并显示在数码显示块上。如选择自动发送则改变数据发送栏中的数字，数据就自动发送至51板。（注：发送数据时数据必为2位16进制数，不足添0，如00，01，02，33，44，AF。）
-microcontroller and PC serial communications open the first examples of serial debugging procedures as requested. Plate start after 51, according to S10 switch to the receiving state, according S12 switch to this state, the start of this default state. Send state : Entering this state, the PC can be sent to 1 -9 9 figures. and digital display shows the number sent by sending an S1, S2 sent by 2, followed by S9 sent to nine. S11 useless. Send success in the serial debugging procedures column indicates data reception of the data received. Send state : Entering this state, Serial debugging procedures in the importation of data this column 00-FF 229 2 16 median, sending it manually, If this success, 51 to 16-band version passed by conversion to 10 and 229 the number displayed on the digital di Platform: |
Size: 976 |
Author:后果发挥 |
Hits:
Description: 模拟一个petri网的行为。该程序应该读入一组转换规则，以及一组状态列表，这些状态对应于网络链路层发出了一个新分组或者接受一个新分组，初始状态也是要读入的。该程序应该从初始状态开始，随机地选择那些激活的转换，并激发这些状态，检查一下看是否有“一个主机接受了2个分组而另一台主机并没有在此期间发出新的分组”这样的情形。-simulated a petri nets behavior. The procedure should be read into one group conversion rules, and a list of the state group, These conditions correspond to link layer network issued a new group or accept a new grouping, initial state is to be read into the. The procedure should start from the initial state, randomly selecting those activated conversion, and to stimulate these states, check to see if it "one of the hosts for a two and the other host has not issued during this period of a new" the same situation. Platform: |
Size: 1356 |
Author:sherry |
Hits:
Description: 本设 计 将 转换结束状态线STS与单片机的P1.7 相连，启动转换信号CE由单
片机的丽和丽相与所得，采用查询方式来读取AD574A的转换结果，由AO来
控制读取高8位和低4位。-the design will change end of the state line STS and SCM P1.7 connected, CE start converting signals from the MCU Laguna and Laguna phase proceeds, using inquiry to read AD574A the conversion results from AO to control read high and low eight four. Platform: |
Size: 82612 |
Author:zmx |
Hits:
Description: TLV1544与TMS320VC5402通过串行口连接，此时，A／D转换芯片作为从设备，DSP提供帧同步和输入／输出时钟信号。TLV1544与DSP之间数据交换的时序图如图3所示。
开始时， 为高电平（芯片处于非激活状态），DATA IN和I/OCLK无效，DATAOUT处于高阻状态。当串行接口使CS变低（激活），芯片开始工作，I／OCLK和DATAIN能使DATA OUT不再处于高阻状态。DSP通过I／OCLK引脚提供输入／输出时钟8序列，当由DSP提供的帧同步脉冲到来后，芯片从DATA IN接收4 b通道选择地址，同时从DATAOUT送出的前一次转换的结果，由DSP串行接收。I／OCLK接收DSP送出的输入序列长度为10～16个时钟周期。前4个有效时钟周期，将从DATAIN输入的4 b输入数据装载到输入数据寄存器，选择所需的模拟通道。接下来的6个时钟周期提供模拟输入采样的控制时间。模拟输入的采样在前10个I／O时钟序列后停止。第10个时钟沿（确切的I／O时钟边缘，即上升沿或下降沿，取决于操作的模式选择）将EOC变低，转换开始。
-TLV1544 with TMS320VC5402 through serial port connectivity, at this time, A / D conversion chip as from the equipment, to provide frame synchronization DSP and input / output clock signal. TLV1544 DSP and data exchange between the chronology of the map is shown in figure 3. At the beginning of the margin (in chip-activated), and I DATA IN / OCLK invalid, DATAOUT at high resistance state. When the serial interface CS change low (activator), the chip start work, I / OCLK and DATAIN can DATA OUT is no longer in a state of high resistance. DSP through I / OCLK pin provide input / output clock 8 sequence, When the DSP from the frame synchronization pulse, the chip from the DATA IN receive four channels to choose b address, DATAOUT sent from the same time the previous conversion results from the Platform: |
Size: 1207 |
Author:john |
Hits:
Description: This program demonstrates operation of ADC0 in polled mode. The ADC0 is
// configured to use writes to AD0BUSY as its start of conversion source and
// to measure the output of the on-chip temperature sensor. The temperature
// sensor output is converted to degrees Celsius and is transmitted out UART0 Platform: |
Size: 2590 |
Author:梧桐 |
Hits:
Description: This program demonstrates operation of ADC0 in polled mode. The ADC0 is
// configured to use writes to AD0BUSY as its start of conversion source and
// to measure the output of the on-chip temperature sensor. The temperature
// sensor output is converted to degrees Celsius and is transmitted out UART0 Platform: |
Size: 45575 |
Author:梧桐 |
Hits:
Description: 本程序中的搜索引擎为王小春的《PC游戏编程(人机博弈)》书中的搜索引擎,估值函数和开局库皆为自己设计.内含大量开局库资料和开局库格式转换程序.本版棋力比1.0版棋力增强不少。 发布此程序代码之用意在于提高我国共享象棋软件的棋力,让我们大家一起来开发开源的中国象棋软件.-the procedures for the search engine to guan "PC game programming (man-machine game)" book search engine, and the valuation function for both start their own design. Start library contains a lot of information and start procedures for format conversion. 1.0% spotlight than many enhanced version of chess. Published this code was intended to enhance our shared the spotlight chess software, so we can together open-source software in Chinese chess. Platform: |
Size: 5318413 |
Author:王明 |
Hits:
Description: Drag and Drop Component Suite Version 4.1 Field test 5, released 16-dec-2001 ?1997-2001 Angus Johnson & Anders Melander http://www.melander.dk/delphi/dragdrop/ ------------------------------------------- Table of Contents: ------------------------------------------- 1. Supported platforms 2. Installation 3. Getting started 4. Known problems 5. Support and feedback 6. Bug reports 7. Upgrades and bug fixes 8. Missing in this release 9. New in version 4.x 10. TODO 11. Licence, Copyright and Disclaimer 12. Release history ------------------------------------------- 1. Supported platforms: ------------------------------------------- This release supports Delphi 4-6 and C++ Builder 4-5. Earlier versions of Delphi and C++ Builder will not be supported. If you need Delphi 3 or C++ Builder 3 support you will have to revert to version 3.7 of the Drag and Drop Component Suite. The library has been tested on NT4 service pack 5 and Windows 2000. Windows 95, 98, ME and XP should be supported, but has not been tested. Linux and Kylix are not supported. There are *NO* plans to port the library to Kylix. The drag and drop protocols available on Linux are too much of a mess at this time. ------------------------------------------- 2. Installation: ------------------------------------------- 1) Before you do anything else, read the "Known problems" section of this document. 2) Install the source into a directory of your choice. The files are installed into three directories: DragDrop DragDrop\Components DragDrop\Demo 3) Install and compile the appropriate design time package. The design time packages are located in the Components directory. Each version of Delphi and C++ Builder has its own package; DragDropD6.dpk for Delphi 6, DragDropD5.dpk for Delphi 5, DragDropC5.bpk for C++ Builder 5, etc. 4) Add the Drag and Drop Component Suite components directory to your library path. 5) Load the demo project group: demo\dragdrop_delphi.bpg for Delphi 5 and 6 demo\dragdrop_bcb4.bpg for C++ Builder 4 demo\dragdrop_bcb5.bpg for C++ Builder 5 The project group contains all the demo applications. 6) If your version of Delphi does not support text format DFM files (e.g. Delphi 4 doesn't), you will have to use the convert.exe utility supplied with Delphi to convert all the demo form files to binary format. A batch file, convert_forms_to delphi_4_format.bat, is supplied in the demo directory which automates the conversion process. The C++ Builder demo forms are distributed in binary format. 7) If upgrading from a previous version of the Drag and Drop Component Suite, please read the document "upgrading_to_v4.txt" before you begin working on your existing projects. Note about "Property does not exist" errors: Since all demos were developed with the latest version of Delphi, most of the demo forms probably contains references to properties that doesn't exist in earlier versions of Delphi and C++ Builder. Because of this you will get fatal run-time errors (e.g. "Error reading blahblahblah: Property does not exist.") if you attemt to run the demos without fixing this problem. Luckily it is very easy to make the forms work again; Just open the forms in the IDE, then select "Ignore All" when the IDE complains that this or that property doesn't exist and finally save the forms. ------------------------------------------- 3. Getting started: ------------------------------------------- It is recommended that you start by running each of the demo applications and then look through the demo source. Each demo application is supplied with a readme.txt file which briefly describes what the demo does and what features it uses. The demos should be run in the order in which they are listed in the supplied project group. Even if you have used previous versions of the Drag and Drop Component Suite it would be a good idea to have a quick look at the demos. The library has been completely rewritten and a lot of new features has been added. ------------------------------------------- 4. Known problems: ------------------------------------------- * The Shell Extension components does not support C++ Builder 4. For some strange reason the components causes a link error. * There appear to be sporadic problems compiling with C++ Builder 5. Several user have reported that they occasionally get one or more of the following compiler errors: [C++ Error] DragDropFile.hpp(178): E2450 Undefined structure '_FILEDESCRIPTORW' [C++ Error] DropSource.hpp(135): E2076 Overloadable operator expected I have not been able to reproduce these errors, but I believe the following work around will fix the problem: In the project options of *all* projects which uses these components, add the following conditional define: NO_WIN32_LEAN_AND_MEAN The define *must* be made in the project options. It is not sufficient to #define it in the source. If you manage to compile with C++ Builder (any version), I would very much like to know about it. * Delphi's and C++ Builder's HWND and THandle types are not compatible. For this reason it might be nescessary to cast C++ Builder's HWND values to Delphi's THandle type when a HWND is passed to a function. E.g.: if (DragDetectPlus(THandle(MyControl->Handle), Point(X, Y))) { ... } * Virtual File Stream formats can only be pasted from the clipboard with live data (i.e. FlushClipboard/OleFlushClipboard hasn't been called on the data source). This problem affects TFileContentsStreamOnDemandClipboardFormat and the VirtualFileStream demo. This is believed to be a bug in the Windows clipboard and a work around hasn't been found yet. * Asynchronous targets appears to be broken in the current release. * When TDropFileTarget.GetDataOnEnter is set to True, the component doesn't work with WinZip. Although the file names are received correctly by TDropFileTarget, WinZip doesn't extract the files and the files thus can't be copied/moved. This is caused by a quirk in WinZip; Apparently WinZip doesn't like IDataObject.GetData to be called before IDropTarget.Drop is called. ------------------------------------------- 5. Support and feedback: ------------------------------------------- Since these components are freeware they are also unsupported. You are welcome to ask for help via email, but I cannot guarantee that I will have time to help you or even reply to your mail. If you absolytely can't live without my help, you can alway try bribing me. You can also try asking for help in the Delphi newsgroups. Since the Drag and Drop Component Suite is in widespread use, there's a good chance another user can help you. I recommend the following newsgroups for issues regarding this library (or COM based Drag/Drop in general): borland.public.delphi.winapi borland.public.delphi.thirdparty-tools borland.public.delphi.oleautomation borland.public.cppbuilder.winapi borland.public.cppbuilder.thirdparty-tools Please choose the most appropiate newsgroup for your question. Do not cross post to them all. Before posting to the newsgroups, I suggest you try to search for an answer on the Google (DejaNews) search engine: http://groups.google.com Chances are that your question has been asked and answered before. If you have suggestions for improvements please mail them to me: anders@melander.dk Please include the words "Drag Drop" in the subject of any email regarding these components. ------------------------------------------- 6. Bug reports: ------------------------------------------- Bugs can either be reported at my home page (http://www.melander.dk/) or mailed directly to me: anders@melander.dk. When reporting a bug, please provide the following information: * The exact version of the Drag and Drop Component Suite you are using. * The exact version of Delphi or C++ Builder you are using. * The name and exact version of your operating system (e.g. NT4 SP5). * The exact version of the Internet Explorer installed on your system. If you can provide me with a minimal application which reproduces the problem, I can almost guarantee that I will be able to fix the problem in very short time. Please supply only the source files (pas, dfm, dpr, dof, res, etc.) and mail them as a single zip file. If I need a compiled version I will ask for it. If you feel you need to send me a screen shot, please send it in GIF or PNG format. If you mail a bug report to me, please include the words "Drag Drop" in the subject of your email. ------------------------------------------- 7. Upgrades and bug fixes: ------------------------------------------- Upgrades can be downloaded from my home page: http://www.melander.dk/delphi/dragdrop/ Bug fixes will also be posted to the above page. If you have registered for update notification via the installation program, you will receive email notification when a new release is available. You will not be notified of bug fixes. You can use the installation program to check for and download new releases and to check for known bugs. Note: If a new release is made available and you are not notified even though you registered for notification, you probably mistyped your email address during installation; About 10% of all registrations supply an invalid email address. ------------------------------------------- 8. Missing in this release: ------------------------------------------- * On-line help has not been updated and included in the kit due to late changes in the Delphi 6 help system and lack of time. If time permits, I will update the help and include it in a future release. ------------------------------------------- 9. New in version 4.x: ------------------------------------------- * Completely redesigned and rewritten. Previous versions of the Drag and Drop Component Suite used a very monolithic design and flat class hierachy which made it a bit cumbersome to extend the existing components or implement new ones. Version 4 is a complete rewrite and redesign, but still maintains compatibility with previous versions. The new V4 design basically separates the library into three layers: 1) Clipboard format I/O. 2) Data format conversion and storage. 3) COM Drag/Drop implementation and VCL component interface. The clipboard format layer is responsible for reading and writing data in different formats to and from an IDataObject interface. For each different clipboard format version 4 implements a specialized class which knows exactly how to interpret the clipboard format. For example the CF_TEXT (plain text) clipboard format is handled by the TTextClipboardFormat class and the CF_FILE (file names) clipboard format is handled by the TFileClipboardFormat class. The data format layer is primarily used to render the different clipboard formats to and from native Delphi data types. For example the TTextDataFormat class represents all text based clipboard formats (e.g. TTextClipboardFormat) as a string while the TFileDataFormat class represents a list of file names (e.g. TFileClipboardFormat) as a string list. The conversion between different data- and clipboard formats is handled by the same Assign/AssignTo mechanism as the VCLs TPersistent employes. This makes it possible to extend existing data formats with support for new clipboard formats without modification to the existing classes. The drag/drop component layer has several tasks; It implements the actual COM drag/drop functionality (i.e. it implements the IDropSource, IDropTarget and IDataObject interfaces (along with several other related interfaces)), it surfaces the data provided by the data format layer as component properties and it handles the interaction between the whole drag/drop framework and the users code. The suite provides a multitude of different components. Most are specialized for different drag/drop tasks (e.g. the TDropFileTarget and TDropFilesSource components for drag/drop of files), but some are either more generic, handling multiple unrelated formats, or simply helper components which are used to extend the existing components or build new ones. * Support for Delphi 6. Version 4.0 was primarily developed on Delphi 6 and then ported back to previous versions of Delphi and C++ Builder. * Support for Windows 2000 inter application drag images. On Windows platforms which supports it, drag images are now displayed when dragging between applications. Currently only Windows 2000 supports this feature. On platforms which doesn't support the feature, drag images are only displayed whithin the source application. * Support for Windows 2000 asynchronous data transfers. Asynchronous data tranfers allows the drop source and targets to perform slow transfers or to transfer large amounts of data without blocking the user interface while the data is being transfered. For platforms other than Windows 2000, the new TDropSourceThread class can be used to provide similar (but more limited) asynchronous data transfer capabilities. * Support for optimized and non-optimized move. When performing drag-move operations, it is now possible to specify if the target (optimized move) or the source (non-optimized move) is responsible for deleting the source files. * Support for delete-on-paste. When data is cut to the clipboard, it is now possible to defer the deletion of the source data until the target actually pastes the data. The source is notified by an event when the target pastes the data. * Extended clipboard support. All formats and components (both source and target) now support clipboard operations (copy/cut/paste) and the VCL clipboard object. * Support for shell drop handlers. The new TDropHandler component can be used to write drop handler shell extensions. A drop handler is a shell extension which is executed when a user drags and drops one or more files on a file associated wth your application. * Support for shell drag drop handlers. The new TDragDropHandler component can be used to write drag drop handler shell extensions. A drag drop handler is a shell extension which can extend the popup menu which is displayed when a user drag and drops files with the right mouse button. * Support for shell context menu handlers. The new TDropContextMenu component can be used to write context menu handler shell extensions. A context menu handler is a shell extension which can extend the popup menu which is displayed when a user right-clicks a file in the shell. * Drop sources can receive data from drop targets. It is now possible for drop targets to write data back to the drop source. This is used to support optimized-move, delete-on-paste and inter application drag images. * Automatic re-registration of targets when the target window handle is recreated. In previous versions, target controls would loose their ability to accept drops when their window handles were recreated by the VCL (e.g. when changing the border style or docking a form). This is no longer a problem. * Support for run-time definition of custom data formats. You can now add support for new clipboard formats without custom components. * Support for design-time extension of existing source and target components. Using the new TDataFormatAdapter component it is now possible to mix and match data formats and source and target components at design time. E.g. the TDropFileTarget component can be extended with URL support. * It is now possible to completely customize the target auto-scroll feature. Auto scroling can now be completely customized via the OnDragEnter, OnDragOver, OnGetDropEffect and OnScroll events and the public NoScrollZone and published AutoScroll properties. * Multiple target controls per drop target component. In previous versions you had to use one drop target component per target control. With version 4, each drop target component can handle any number of target controls. * It is now possible to specify the target control at design time. A published Target property has been added to the drop target components. * Includes 20 components: - TDropFileSource and TDropFileTarget Used for drag and drop of files. Supports recycle bin and PIDLs. - TDropTextSource and TDropTextTarget Used for drag and drop of text. - TDropBMPSource and TDropBMPTarget Used for drag and drop of bitmaps. - TDropPIDLSource and TDropPIDLTarget Used for drag and drop of PIDLs in native format. - TDropURLSource and TDropURLTarget Used for drag and drop of internet shortcuts. - TDropDummyTarget Used to provide drag/drop cursor feedback for controls which aren't registered as drop targets. - TDropComboTarget (new) Swiss-army-knife target. Accepts text, files, bitmaps, meta files, URLs and file contents. - TDropMetaFileTarget (new) Target which can accept meta files and enhanced meta files. - TDropImageTarget (new) Target which can accept bitmaps, DIBs, meta files and enhanced meta files. - TDragDropHandler (new) Used to implement Drag Drop Handler shell extensions. - TDropHandler (new) Used to implement Shell Drop Handler shell extensions. - TDragDropContext (new) Used to implement Shell Context Menu Handler shell extensions. - TDataFormatAdapter (new) Extends the standard source and target components with support for extra data formats. An alternative to TDropComboTarget. - TDropEmptySource and TDropEmptyTarget (new) Target and source components which doesn't support any formats, but can be extended with TDataFormatAdapter components. * Supports 27 standard clipboard formats: Text formats: - CF_TEXT (plain text) - CF_UNICODETEXT (Unicode text) - CF_OEMTEXT (Text in the OEM characterset) - CF_LOCALE (Locale specification) - 'Rich Text Format' (RTF text) - 'CSV' (Tabular spreadsheet text) File formats: - CF_HDROP (list of file names) - CF_FILEGROUPDESCRIPTOR, CF_FILEGROUPDESCRIPTORW and CF_FILECONTENTS (list of files and their attributes and content). - 'Shell IDList Array' (PIDLs) - 'FileName' and 'FileNameW' (single filename, used for 16 bit compatibility). - 'FileNameMap' and 'FileNameMapW' (used to rename files, usually when dragging from the recycle bin) Image formats: - CF_BITMAP (Windows bitmap) - CF_DIB (Device Independant Bitmap) - CF_METAFILEPICT (Windows MetaFile) - CF_ENHMETAFILE (Enhanced Metafile) - CF_PALETTE (Bitmap palette) Internet formats: - 'UniformResourceLocator' and 'UniformResourceLocatorW' (Internet shortcut) - 'Netscape Bookmark' (Netscape bookmark/URL) - 'Netscape Image Format' (Netscape image/URL) - '+//ISBN 1-887687-00-9::versit::PDI//vCard' (V-Card) - 'HTML Format' (HTML text) - 'Internet Message (rfc822/rfc1522)' (E-mail message in RFC822 format) Misc. formats: - CF_PREFERREDDROPEFFECT and CF_PASTESUCCEEDED (mostly used by clipboard) - CF_PERFORMEDDROPEFFECT and CF_LOGICALPERFORMEDDROPEFFECT (mostly used for optimized-move) - 'InShellDragLoop' (used by Windows shell) - 'TargetCLSID' (Mostly used when dragging to recycle-bin) * New source events: - OnGetData: Fired when the target requests data. - OnSetData: Fired when the target writes data back to the source. - OnPaste: Fired when the target pastes data which the source has placed on the clipboard. - OnAfterDrop: Fired after the drag/drop operation has completed. * New target events: - OnScroll: Fires when the target component is about to perform auto-scroll on the target control. - OnAcceptFormat: Fires when the target component needs to determine if it will accept a given data format. Only surfaced in the TDropComboTarget component. * 8 new demo applications, 19 in total. ------------------------------------------- 10. TODO (may or may not be implemented): ------------------------------------------- * Async target demo (with and without IAsyncOperation support). * Scrap file demo. * Native Outlook message format. * Structured storage support (IStorage encapsulation). ------------------------------------------- 11. Licence, Copyright and Disclaimer: ------------------------------------------- The Drag and Drop Component Suite is Copyright ?1997-2001 Angus Johnson and Anders Melander. All rights reserved. The software is copyrighted as noted above. It may be freely copied, modified, and redistributed, provided that the copyright notice(s) is preserved on all copies. The Drag and Drop Component Suite is freeware and we would like it to remain so. This means that it may not be bundled with commercial libraries or sold as shareware. You are welcome to use it in commercial and shareware applications providing you do not charge for the functionality provided by the Drag and Drop Component Suite. There is no warranty or other guarantee of fitness for this software, it is provided solely "as is". You are welcome to use the source to make your own modified components, and such modified components may be distributed by you or others if you include credits to the original components, and do not charge anything for your modified components. ------------------------------------------- 12. Version 4 release history: ------------------------------------------- 16-dec-2001 * Ported to C++ Builder 4. * Released for test as v4.1 FT5. 12-dec-2001 * Fixed C++ Builder name clash between TDropComboTarget.GetMetaFile and the GetMetaFile #define in wingdi.h 1-dec-2001 * The IAsyncOperation interface is now also declared as IAsyncOperation2 and all references to IAsyncOperation has been replaced with IAsyncOperation2. This was done to work around a bug in C++ Builder. Thanks to Jonathan Arnold for all his help with getting the components to work with C++ Builder. Without Jonathan's help version 4.1 would prabably have shipped witout C++ Builder support and certainly without any C++ Builder demos. * Demo applications for C++ Builder. The C++ Builder demos were contributed by Jonathan Arnold. 27-nov-2001 * TCustomDropTarget.Droptypes property renamed to DropTypes (notice the case). Thanks to Krystian Brazulewicz for spotting this. 24-nov-2001 * The GetURLFromString function in the DragDropInternet unit has been made public due to user request. 21-nov-2001 * Modified MakeHTML function to comply with Microsoft's description of the CF_HTML clipboard format. * Added MakeTextFromHTML function to convert CF_HTML data to plain HTML. Provides the reverse functionality of MakeHTML. * Added HTML support to TTextDataFormat class and TDropTextSource and TDropTextTarget components. * Fixed C++ Builder 5 problem with IAsyncOperation. * Released for test as v4.1 FT4. 10-nov-2001 * Added NetscapeDemo demo application. Demonstrates how to receive messages dropped from Netscape. This demo was sponsored by ThoughtShare Communications Inc. * Released for test as v4.1 FT3. 23-oct-2001 * Conversion priority of TURLDataFormat has been changed to give the File Group Descritor formats priority over the Internet Shortcut format. This resolves a problem where dropping an URL on the desktop would cause the desktop to assume that an Active Desktop item was to be created instead of an Internet Shortcut. Thanks to Allen Martin for reporting this problem. By luck this modification also happens to work around a bug in Mozilla and Netscape 6; Mozilla incorrectly supplies the UniformResourceLocator clipboard format in unicode format instead of ANSI format. Thanks to Florian Kusche for reporting this problem. * Added support for TFileGroupDescritorWClipboardFormat to TURLDataFormat. * Added declaration of FD_PROGRESSUI to DragDropFormats. * Added TURLWClipboardFormat which implements the "UniformResourceLocatorW" (a.k.a. CFSTR_INETURLW) clipboard format. Basically a Unicode version of CFSTR_SHELLURL/CFSTR_INETURL. The TURLWClipboardFormat class isn't used anywhere yet but will probably be supported by TURLDataFormat (and thus TDropURLTarget/TDropURLSource) in a later release. * Added experimental Shell Drag Image support. This relies on undodumented shell32.dll functions and probably won't be fully support before v4.2 (if ever). See InitShellDragImage in DropSource.pas. Thanks to Jim Kueneman for bringning these functions to my attention. 13-oct-2001 * TCustomDropSource.Destroy and TCustomDropMultiSource.Destroy changed to call FlushClipboard instead of EmptyClipboard. This means that clipboard contents will be preserved when the source application/component is terminated. * Added clipboard support to VirtualFileStream demo. * Modified VirtualFileStream demo to work around clipboard quirk with IStream medium. * Modified TCustomSimpleClipboardFormat to disable TYMED_ISTORAGE support by default. At present TYMED_ISTORAGE is only supported for drop targets and enabling it by default in TCustomSimpleClipboardFormat.Create caused a lot of clipboard operations (e.g. copy/paste of text) to fail. Thanks to Michael J Marshall for bringing this problem to my attention. * Modified TCustomSimpleClipboardFormat to read from the the TYMED_ISTREAM medium in small (1Mb) chunks and via a global memory buffer. This has resultet in a huge performance gain (several orders of magnitude) when transferring large amounts of data via the TYMED_ISTREAM medium. 3-oct-2001 * Fixed bug in TCustomDropSource.SetImageIndex. Thanks to Maxim Abramovich for spotting this. * Added missing default property values to TCustomDropSource. Thanks to Maxim Abramovich for spotting this. * DragDrop.pas and DragDropContext.pas updated for Delphi 4. * Reimplemented utility to convert DFM form files from Delphi 5/6 test format to Delphi 4/5 binary format. * Improved unregistration of Shell Extensions. Shell extension now completely (and safely) remove their registry entries when unregistered. * Deprecated support for C++ Builder 3. * Released for test as v4.1 FT2. 25-sep-2001 * Rewritten ContextMenuHandlerShellExt demo. The demo is now actually a quite useful utility which can be used to register and unregister ActiveX controls, COM servers and type libraries. It includes the same functionality as Borland's TRegSvr utility. 20-sep-2001 * Added support for cascading menus, ownerdraw and menu bitmaps to TDropContextMenu component. * Modified TFileContentsStreamOnDemandClipboardFormat to handle invalid parameter value (FormatEtcIn.lindex) when data is copied to clipboard. This works around an apparent bug in the Windows clipboard. Thanks to Steve Moss for reporting this problem. * Modified TEnumFormatEtc class to not enumerate empty clipboard formats. Thanks to Steve Moss for this improvement. 1-sep-2001 * Introduced TCustomDropTarget.AutoRegister property. The AutoRegister property is used to control if drop target controls should be automatically unregistered and reregistered when their window handle is recreated by the VCL. If AutoRegister is True, which is the default, then automatic reregistration will be performed. This property was introduced because the hidden child control, which is used to monitor the drop target control's window handle, can have unwanted side effects on the drop target control (e.g. TToolBar). * Deprecated support for Delphi 3. 22-jun-2001 * Redesigned TTextDataFormat to handle RTF, Unicode, CSV and OEM text without conversion. Moved TTextDataFormat class to DragDropText unit. Added support for TLocaleClipboardFormat. * Surfaced new text formats as properties in TDropTextSource and TDropTextTarget. Previous versions of the Text source and target components represented all supported text formats via the Text property. In order to enable users to handle the different text formats independantly, the text source and target components now has individual properties for ANSI, OEM, Unicode and RTF text formats. The text target component can automatically synthesize some of the formats from the others (e.g. OEM text from ANSI text), but applications which previously relied on all formats being represented by the Text property will have to be modified to handle the new properties. * Added work around for problem where TToolBar as a drop target would display the invisible target proxy window. * Fixed wide string bug in WriteFilesToZeroList. Thanks to Werner Lehmann for spotting this. 15-jun-2001 * Added work-around for Outlook Express IDataObject.QueryGetData quirk. 3-jun-2001 * Ported to C++ Builder 4 and 5. * Added missing DragDropDesign.pas unit to design time packages. * First attempt at C++ Builder 3 port.... failed. * Improved handling of oversized File Group Descriptor data. * Added support for IStorage medium to TFileContentsStreamClipboardFormat. This allows the TDropComboTarget component to accept messages dropped from Microsoft Outlook. This work was sponsored by ThoughtShare Communications Inc. 23-may-2001 * Ported to Delphi 4. * First attempt at C++ Builder 5 port.... failed. 18-may-2001 * Released as version 4.0. Note: Version 4.0 was released exclusively on the Delphi 6 Companion CD. * ContextMenuDemo and DropHandlerDemo application has been partially rewritten and renamed. ContextMenuDemo is now named ContextMenuHandlerShellExt. DropHandlerDemo is now named DropHandlerShellExt. * TDropContextMenu component has been rewitten. The TDropContextMenu now implements a context menu handler shell extension. In previous releases it implemented a drag drop handler shell extension. * The DragDropHandler.pas unit which implements the TDropHandler component has been renamed to DropHandler.pas. * Added new TDragDropHandler component. The new component, which lives in the DragDropHandler unit, is used to implement drag drop handler shell extensions. * Added DragDropHandlerShellExt demo application. * Removed misc incomplete demos from kit. * Fixed minor problem in VirtualFileStream demo which caused drops from the VirtualFile demo not to transfer content correctly. 11-may-2001 * Converted all demo forms to text DFM format. This has been nescessary to maintain compatibility between all supported versions of Delphi. * Fixed a bug in GetPIDLsFromFilenames which caused drag-link of files (dtLink with TDropFileSource) not to work. * Added readme.txt files to some demo applications. * Added missing tlb and C++ Builder files to install kit. * Released as FT4. 6-may-2001 * Added missing dfm files to install kit. * Tested with Delphi 5. Fixed Delphi 5 compatibility error in main.dfm of DragDropDemo. * Removed misc compiler warnings. * The AsyncTransferTarget and OleObjectDemo demos were incomplete and has been removed from the kit for the V4.0 release. The demos will be included in a future release. * Released as FT3. 3-may-2001 * Added missing dpr and bpg files to install kit. * Updated readme.txt with regard to lack of C++ Builder demos. * Released as FT2. 29-apr-2001 * Cleaned up for release. * Released as FT1. 23-feb-2001 * Modified TCustomDropTarget.FindTarget to handle overlapping targets (e.g. different targets at the same position but on different pages of a page control or notebook). Thanks to Roger Moe for spotting this problem. 13-feb-2001 * Renamed AsyncTransfer2 demo to AsyncTransferSource. * Added AsyncTransferTarget demo. * Replaced TChart in AsyncTransfer2 demo with homegrown pie-chart-thing. * Modified all IStream based target formats to support incremental transfer. * URW533 problem has finally been fixed. The cause of the problem, which is a bug in Delphi, was found by Stefan Hoffmeister. * Fixed free notification for TDropContextmenu and TDataFormatAdapter. 27-dec-2000 * Moved TVirtualFileStreamDataFormat and TFileContentsStreamOnDemandClipboardFormat classes from VirtualFileStream demo to DragDropFormats unit. * Added TClipboardFormat.DataFormat and TClipboardFormats.DataFormat property. * Added TDropEmptySource and TDropEmptyTarget components. These are basically do-nothing components for use with TDataFormatAdapter. * Rewritten AsyncTransfer2 demo. The demo now uses TDropEmptySource, TDataFormatAdapter and TVirtualFileStreamDataFormat to transfer 10Mb of data with progress feedback. * Rewritten VirtualFileStream demo. The demo now uses TDropEmptySource, TDropEmptyTarget, TDataFormatAdapter and TVirtualFileStreamDataFormat. * Fixed memory leak in TVirtualFileStreamDataFormat. This leak only affected the old VirtualFileStream demo. * Added support for full File Descriptor attribute set to TVirtualFileStreamDataFormat. It is now possible to specify file attributes such as file size and last modified time in addition to the filename. I plan to add similar features to the other classes which uses FileDescriptors (e.g. TDropFileSource and TDropFileTarget). 21-dec-2000 * Ported to Delphi 4. * Added workaround for design bug in either Explorer or the clipboard. Explorer and the clipboard's requirements to the cursor position of an IStream object are incompatible. Explorer requires the cursor to be at the beginning of stream and the clipboard requires the cursor to be at the end of stream. 15-dec-2000 * Fixed URW533 problem. I'll leave the description of the workaround in here for now in case the problem resurfaces. 11-dec-2000 * Fixed bug in filename to PIDL conversion (GetPIDLsFromFilenames) which affected TDropFileTarget. Thanks to Poul Halgaard J鴕gensen for reporting this. 4-dec-2000 * Added THTMLDataFormat. * Fixed a a few small bugs which affected clipboard operations. * Added {$ALIGN ON} to dragdrop.inc. Apparently COM drag/drop requires some structures to be word alligned. This change fixes problems where some of the demos would suddenly stop working. * The URW533 problem has resurfaced. See the "Known problems" section below. 13-nov-2000 * TCopyPasteDataFormat has been renamed to TFeedbackDataFormat. * Added support for the Windows 2000 "TargetCLSID" format with the TTargetCLSIDClipboardFormat class and the TCustomDropSource.TargetCLSID property. * Added support for the "Logical Performed DropEffect" format with the TLogicalPerformedDropEffectClipboardFormat class. The class is used internally by TCustomDropSource. 30-oct-2000 * Added ContextMenu demo and TDropContextMenu component. Demonstrates how to customize the context menu which is displayed when a file is dragged with the right mouse button and dropped in the shell. * Added TCustomDataFormat.GetData. With the introduction of the GetData method, Data Format classes can now be used stand-alone to extract data from an IDataObject. 20-oct-2000 * Added VirtualFileStream demo. Demonstrates how to use the "File Contents" and "File Group Descritor" clipboard formats to drag and drop virtual files (files which doesn't exist physically) and transfer the data on-demand via a stream. 14-oct-2000 * Added special drop target registration of TCustomRichEdit controls. TCustomRichEdit needs special attention because it implements its own drop target handling which prevents it to work with these components. TCustomDropTarget now disables a rich edit control's built in drag/drop handling when the control is registered as a drop target. * Added work around for Windows bug where IDropTarget.DragOver is called regardless that the drop has been rejected in IDropTarget.DragEnter. 12-oct-2000 * Fixed bug that caused docking to interfere with drop targets. Thanks to G. Bradley MacDonald for bringing the problem to my attention. 30-sep-2000 * The DataFormats property has been made public in the TCustomDropMultiTarget class. * Added VirtualFile demo. Demonstrates how to use the TFileContentsClipboardFormat and TFileGroupDescritorClipboardFormat formats to drag and drop a virtual file (a file which doesn't exist physically). 28-sep-2000 * Improved drop source detection of optimized move. When an optimized move is performed by a drop target, the drop source's Execute method will now return drDropMove. Previously drCancel was returned. The OnAfterDrop event must still be used to determine if a move operation were optimized or not. * Modified TCustomDropTarget.GetPreferredDropEffect to get data from the current IDataObject instead of from the VCL global clipboard. 18-sep-2000 * Fixed bug in DropComboTarget caused by the 17-sep-2000 TStreams modification. 17-sep-2000 * Added AsyncTransfer2 demo to demonstrate use of TDropSourceThread. * Renamed TStreams class to TStreamList. 29-aug-2000 * Added TDropSourceThread. TDropSourceThread is an alternative to Windows 2000 asynchronous data transfers but also works on other platforms than Windows 2000. TDropSourceThread is based on code contributed by E. J. Molendijk. 24-aug-2000 * Added support for Windows 2000 asynchronous data transfers. Added IAsyncOperation implementation to TCustomDropSource. Added TCustomDropSource.AllowAsyncTransfer and AsyncTransfer properties. 5-aug-2000 * Added work around for URW533 compiler bug. * Fixed D4 and D5 packages and updated a few demos. Obsolete DropMultiTarget were still referenced a few places. * Documented work around for C++ Builder 5 compiler error. See the Known Problems section later in this document for more information. 2-aug-2000 * The package files provided in the kit is now design-time only packages. In previous versions, the packages could be used both at design- and run-time. The change was nescessary because the package now contains design-time code. * Added possible work around for suspected C++ Builder bug. The bug manifests itself as a "Overloadable operator expected" compile time error. See the "Known problems" section of this document. * Rewrote CustomFormat1 demo. * Added CustomFormat2 demo. * TDataDirection members has been renamed from ddGet and ddSet to ddRead and ddWrite. * All File Group Descritor and File Contents clipboard formats has been moved from the DragDropFile unit to the DragDropFormats unit. * File Contents support has been added to TTextDataFormat. The support is currently only enabled for drop sources. * Renamed TDropMultiTarget component to TDropComboTarget. Note: This will break applications which uses the TDropMultiTarget component. You can use the following technique to port application from previous releases: 1) Install the new components. 2) Repeat step 3-8 for all units which uses the TDropMultiTarget component. 3) Make a backup of the unit (both pas and dfm file) just in case... 4) Open the unit in the IDE. 5) In the .pas file, replace all occurances of "TDropMultiTarget" with "TDropComboTarget". 6) View the form as text. 7) Replace all occurances of "TDropMultiTarget" with "TDropComboTarget". 8) Save the unit. * Renamed a lot of demo files and directories. * Added work around for yet another bug in TStreamAdapter. * Added TCustomStringClipboardFormat as new base class for TCustomTextClipboardFormat. This changes the class hierachy a bit for classes which previously descended from TCustomTextClipboardFormat: All formats which needs zero termination now descend from TCustomTextClipboardFormat and the rest descend from TCustomStringClipboardFormat. Added TrimZeroes property. Fixed zero termination bug in TCustomTextClipboardFormat and generally improved handling of zero terminated strings. Disabled zero trim in TCustomStringClipboardFormat and enabled it in TCustomTextClipboardFormat. 23-jul-2000 * Improved handling of long file names in DropHandler demo. Added work around for ParamStr bug. * Added TDataFormatAdapter component and adapter demo. TDataFormatAdapter is used to extend the existing source and target components with additional data format support without modifying them. It can be considered an dynamic alternative to the current TDropMultiTarget component. 17-jul-2000 * TDropHandler component and DropHandler demo fully functional. 14-jul-2000 * Tested with C++ Builder 5. * Fixed sporadic integer overflow bug in DragDetectPlus function. * Added shell drop handler support with TDropHandler component. This is a work in progress and is not yet functional. 1-jul-2000 * Tested with Delphi 4. * Support for Windows 2000 inter application drag images. * TRawClipboardFormat and TRawDataFormat classes for support of arbitrary unknown clipboard formats. The classes are used internally in the TCustomDropSource.SetData method to support W2K drag images. Platform: |
Size: 2130304 |
Author:smj_9547 |
Hits:
Description: 本程序中的搜索引擎为王小春的《PC游戏编程(人机博弈)》书中的搜索引擎,估值函数和开局库皆为自己设计.内含大量开局库资料和开局库格式转换程序.本版棋力比1.0版棋力增强不少。发布此程序代码之用意在于提高我国共享象棋软件的棋力,让我们大家一起来开发开源的中国象棋软件-the procedures for the search engine to guan "PC game programming (man-machine game)" book search engine, and the valuation function for both start their own design. Start library contains a lot of information and start procedures for format conversion. 1.0% spotlight than many enhanced version of chess. Published this code was intended to enhance our shared the spotlight chess software, so we can together open-source software in Chinese Chess Platform: |
Size: 5318656 |
Author:张建民 |
Hits:
Description: 采用Intel8255端口数据线与上图除IN0~IN7之外的引线连接。
程序步骤：
(1)根据模拟信号输入连线方式(跳线JP10与电位器１相连，若JP10上跳线摘掉，可将电位器２作模拟信号输入)，选择模拟通路，即选定addC,addB,accA组成三位二进制数据；
(2)同时使START和ALE有效，使ADC0809选择相应模拟信号并转换；
(3)等待EOC出现高电平；
(4)使OE为高电平，即允许从ADC0809读出数据
-Intel8255 port using data cable with the exception of the map outside the IN0 ~ IN7 pin connection. Procedural steps: (1) According to the analog signal input connection means (JP10 jumper connected with the potentiometer 1, if the jumper JP10 removed can be Potentiometers for analog signal input 2), select the analog channel, namely, the election set addC, addB, accA composed of three binary data (2) At the same time so that START and ALE effective, so select the appropriate ADC0809 analog signal and conversion (3) wait for EOC appears high (4) to enable the OE for the high electrical ping, which allows读出数据from ADC0809 Platform: |
Size: 1024 |
Author:萧寒 |
Hits:
Description: CCS中用c55x实现AD转换
模数转换相对于计算机来说是一个较为缓慢的过程。一般采用中断方式启动转换或保存
结果，这样在CPU 忙于其他工作时可以少占用处理时间。设计转换程序应首先考虑处理过
程如何与模数转换的时间相匹配，根据实际需要选择适当的触发转换的手段，也要能及时地
保存结果。
由于TMS320VC5509A DSP 芯片内的A/D 转换精度是10 位的，转换结果的低10 位为
所需数值，所以在保留时应注意将结果的高6 位去除，取出低10 位有效数字。-CCS AD conversion using c55x ADC to achieve relative to the computer is a relatively slow process. An interrupt normal start conversion or save the results, so the CPU can be busy with other work less processing time. Design conversion process should first consider how the ADC matches the time, according to the actual need to select the appropriate means to trigger change, we must be able to save the results in time. As TMS320VC5509A DSP chip for A/D conversion precision is 10-bit conversion result of the lower 10 to the desired value, so reservations should pay attention to the results in the high six removed, remove the lower 10 digits. Platform: |
Size: 75776 |
Author:doris |
Hits:
Description: 实现电机SPWM控制，适用于大部分异步电机，如用于同步电机，需变频启动-The motor SPWM control for most of the induction motor, such as for synchronous motor, the need to start conversion Platform: |
Size: 227328 |
Author:shanbaoyus |
Hits:
Description: 430ADC conversion includes the initial configuration of the ADC, ADC start conversion and ADC interrupt Platform: |
Size: 169984 |
Author:李龙 |
Hits:
Search - start conversion